Cabletron Systems Switch FDDI User Manual

7F06-02 FDDI SmartSwitch™  
Interface Module  
User’s Guide  
900331672-02  
 
Only qualified personnel should perform installation  
procedures.  
NOTICE  
Cabletron Systems reserves the right to make changes in specifications and other information  
contained in this document without prior notice. The reader should in all cases consult Cabletron  
Systems to determine whether any such changes have been made.  
The hardware, firmware, or software described in this manual is subject to change without notice.  
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,  
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT  
NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR  
THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN  
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH  
DAMAGES.  
Copyright 1998 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005  
All Rights Reserved  
Printed in the United States of America  
Order Number: 9031672-02 January 1998  
Cabletron Systems, SPECTRUM, and LANVIEW are registered trademarks and SmartSTACK,  
ELS10-26TX, FEPIM, FEPIM-TX and FEPIM-FX are trademarks of Cabletron Systems, Inc.  
All other product names mentioned in this manual may be trademarks or registered trademarks of  
their respective companies.  
FCC NOTICE  
This device complies with Part 15 of the FCC rules. Operation is subject to the following two  
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital  
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable  
protection against harmful interference when the equipment is operated in a commercial environment.  
This equipment uses, generates, and can radiate radio frequency energy and if not installed in  
accordance with the operator’s manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause interference in which case the user  
will be required to correct the interference at his own expense.  
WARNING: Changes or modifications made to this device which are not expressly approved by the  
party responsible for compliance could void the user’s authority to operate the equipment.  
Printed on  
Recycled Paper  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
i
 
Notice  
DOC NOTICE  
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital  
apparatus set out in the Radio Interference Regulations of the Canadian Department of  
Communications.  
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables  
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique  
édicté par le ministère des Communications du Canada.  
VCCI NOTICE  
This is a Class A product based on the standard of the Voluntary Control Council for Interference by  
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,  
radio disturbance may arise. When such trouble occurs, the user may be required to take corrective  
actions.  
CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT  
IMPORTANT: Before utilizing this product, carefully read this License Agreement.  
This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)  
that sets forth your rights and obligations with respect to the Cabletron software program (the  
“Program”) contained in this package. The Program may be contained in firmware, chips or other  
media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME  
BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND  
THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT  
AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED  
PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.  
ii  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
Notice  
CABLETRON SOFTWARE PROGRAM LICENSE  
1.  
LICENSE. You have the right to use only the one (1) copy of the Program provided in this  
package subject to the terms and conditions of this License Agreement.  
You may not copy, reproduce or transmit any part of the Program except as permitted by the  
Copyright Act of the United States or as authorized in writing by Cabletron.  
2.  
3.  
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the  
Program.  
APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws  
and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and  
venue of the New Hampshire courts.  
EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY  
1.  
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in  
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including  
its documentation and media).  
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO  
YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING  
BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND  
FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE  
ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.  
2.  
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL  
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER  
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,  
PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL,  
INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)  
ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT,  
EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH  
DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR  
LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR  
ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME  
INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO  
YOU.  
UNITED STATES GOVERNMENT RESTRICTED RIGHTS  
The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer  
software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the  
Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects  
is proprietary data belonging to Cabletron and/or its suppliers.  
For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the  
DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its  
successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in  
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at  
252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
iii  
 
Notice  
DECLARATION OF CONFORMITY  
Application of Council Directive(s): 89/336/EEC  
73/23/EEC  
Manufacturer’s Name: Ca bletr on System s, In c.  
Manufacturer’s Address: 35 In d u str ia l Wa y  
P O Box 5005  
Roch ester , NH 03867  
European Representative Name: Mr . J . Sola r i  
European Representative Address: Ca bletr on System s Lim ited  
Nexu s Hou se, New bu r y Bu sin ess  
P a r k  
Lon d on Roa d , New bu r y  
Ber k sh ir e RG13 2P Z, En gla n d  
Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC  
EC Directive 73/23/EEC  
EN 55022  
EN 50082-1  
EN 60950  
Equipment Type/Environment: Netw or k in g Equ ip m en t, for u se  
in a Com m er cia l or Ligh t  
In d u str ia l En vir on m en t.  
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged  
with this notice conforms to the above directives.  
Manufacturer  
Legal Representative in Europe  
Mr. Ronald Fotino  
Mr. J. Solari  
___________________________________  
___________________________________  
Full Name  
Full Name  
Principal Compliance Engineer  
Managing Director - E.M.E.A.  
___________________________________  
___________________________________  
Title  
Title  
Rochester, NH, USA  
Newbury, Berkshire, England  
___________________________________  
___________________________________  
Location  
Location  
iv  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
CONTENTS  
CHAPTER 1  
INTRODUCTION  
1.1 Using This Manual....................................................................... 1-1  
1.2 The 7F06-02 Module ................................................................... 1-1  
1.2.1 Cable Type and FPIMs................................................... 1-2  
1.2.2 7C03 MMAC SmartSwitch, the 7C04 Workgroup  
SmartSwitch and the 7C04-R Workgroup  
SmartSwitch.................................................................... 1-3  
1.3 Features ...................................................................................... 1-3  
1.3.1 FPIMs ............................................................................. 1-3  
1.3.2 LANVIEW LEDs.............................................................. 1-3  
1.3.3 Connectivity .................................................................... 1-4  
1.4 Related Manuals.......................................................................... 1-4  
1.5 Getting Help................................................................................. 1-5  
CHAPTER 2  
NETWORK REQUIREMENTS  
2.1 FPIM Module Specifications........................................................ 2-1  
2.1.1 FPIM-00 and FPIM-01 .................................................... 2-1  
2.1.2 FPIM-02 and FPIM-04 .................................................... 2-2  
2.1.3 FPIM-05 and FPIM-07 .................................................... 2-3  
CHAPTER 3  
INSTALLATION/REMOVAL  
3.1 Unpacking The 7F06-02 Module ................................................. 3-1  
3.2 Installing FPIMs........................................................................... 3-2  
3.3 Installing/Removing The 7F06-02 Module................................... 3-3  
3.3.1 Installing in the 7C03 SmartSwitch................................. 3-3  
3.3.2 Removing from the 7C03 SmartSwitch........................... 3-4  
3.3.3 Installing in the 7C04 or 7C04-R  
Workgroup SmartSwitch................................................. 3-5  
3.3.4 Removing the 7F06-02 from the 7C04  
or 7C04-R Workgroup SmartSwitch ............................... 3-8  
CHAPTER 4  
TROUBLESHOOTING  
4.1 Diagnostic and Monitoring System.............................................. 4-1  
4.2 Port Receive LEDs ...................................................................... 4-2  
4.3 Port Transmit LEDs ..................................................................... 4-2  
4.4 A/B Link LEDs ............................................................................. 4-2  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
v
 
Contents  
CHAPTER 5  
TECHNICAL SPECIFICATIONS  
5.1 Standards.....................................................................................5-1  
5.2 EMI...............................................................................................5-1  
5.3 EMC.............................................................................................5-1  
5.4 Network Interfaces.......................................................................5-1  
5.5 Safety...........................................................................................5-2  
5.6 Service.........................................................................................5-2  
5.7 Physical........................................................................................5-2  
5.7.1 Dimensions......................................................................5-2  
5.7.2 Weight .............................................................................5-2  
vi  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
CHAPTER 1  
INTRODUCTION  
Welcome to Cabletron Systems 7F06-02 FDDI SmartSwitch Interface  
Module User Guide. This guide is a simple reference for installing and  
using the 7F06-02 Module. Before installing this module, you should  
carefully read through this manual to gain a full understanding of its  
capabilities.  
The 7F06-02 Module is a two-port FDDI module. This module connects  
to a network and the 7X00 SmartSwitch™ Control Module in the 7C03,  
7C04 or 7C04-R MMAC SmartSwitch via a SmartSwitch bus.  
1.1  
USING THIS MANUAL  
Chapter 1, Introduction, discusses the capabilities and special features of  
Cabletron Systems 7F06-02 Module. This chapter also includes a list of  
related manuals.  
Chapter 2, Network Requirements, contains a list of available FPIMs  
and the network requirements that should be considered before installing  
the 7F06-02 Module.  
Chapter 3, Installation/Removal, contains instructions for installing and  
removing the 7F06-02 in the 7C03 MMAC SmartSwitch, the 7C04  
Workgroup SmartSwitch or the 7C04-R Workgroup SmartSwitch.  
Chapter 4, Troubleshooting, contains instructions for using LANVIEW®  
(Cabletron Systems built-in diagnostic and status monitoring system).  
Chapter 5, Technical Specifications, provides detailed information about  
the physical characteristics of the 7F06-02 Module.  
1.2  
THE 7F06-02 MODULE  
The 7F06-02 Module, shown in Figure 1-1, provides two fiber optic ports  
via front panel FPIM modules.  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
1-1  
 
Chapter 1: Introduction  
1.2.1  
Cable Type and FPIMs  
The 7F06-02 module has two front panel connectors that interface to the  
7X00 SmartSwitch Module through the chassis backplane. The front  
panel connections are standard Cabletron FPIMs. There are two FPIMs  
for each channel. These FPIMs allow the use of single mode or  
multimode fiber cable with MIC or SC type connectors and twisted pair  
cable, either shielded or unshielded.  
7F06-02  
SP  
A
F
D
SN  
P
D
I
1
A
B
S
B
A
F
D
D
I
A
B
P
S
2
B
Figure 1-1 7F06-02 Module  
1-2  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
Chapter 1: Introduction  
1.2.2  
7C03 MMAC SmartSwitch, the 7C04 Workgroup  
SmartSwitch and the 7C04-R Workgroup  
SmartSwitch  
The 7F06-02 Module is designed to be installed in the 7C03 MMAC  
SmartSwitch, the 7C04 Workgroup SmartSwitch or the 7C04-R  
Workgroup SmartSwitch.  
The modular design of the 7C03 MMAC SmartSwitch allows other  
modules that support Ethernet, Fast Ethernet, ATM, FDDI, or Token Ring  
to be used with the 7F06-02 Module. These modules provide the  
capability to share data without the use of external bridges or routers.  
The 7C03 MMAC SmartSwitch is a unique module that can be installed  
in an MMAC Series chassis. The 7C04 Workgroup SmartSwitch and the  
7C04-R Workgroup SmartSwitch are stand-alone chassis that provide the  
same functions.  
1.3  
FEATURES  
The 7F06-02 Module provides two FDDI ports via front panel FPIMs.  
The 7F06-02 Module includes the following features:  
1.3.1  
FPIMs  
The front panel connections are standard Cabletron FPIMs. These  
FPIMs allow the use of single mode or multimode fiber cable with  
MIC or SC type connectors.  
1.3.2  
LANVIEW LEDs  
The 7F06-02 uses LANVIEW, Cabletron Systems built-in visual  
diagnostic and status monitoring system. With LANVIEW LEDs, you can  
quickly identify, at a glance, the status of the device connected to a port  
on the 7F06-02 Module.  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
1-3  
 
Chapter 1: Introduction  
1.3.3  
Connectivity  
The 7F06-02 Module has one backplane connection and two sets of A/B  
front panel FPIM connections. The backplane connection provides power  
to the 7F06-02 Module and a channel for communication with the 7X00  
SmartSwitch Control Module. The two front panel FPIMs provide FDDI  
connections, allowing the use of single mode or multimode fiber cable  
with MIC or SC type connectors.  
1.4  
RELATED MANUALS  
The following Cabletron Systems manuals supplement the procedures  
and other technical data provided in this manual. The procedures will be  
referenced, where appropriate, but will not be repeated.  
7X00 SmartSwitch Control Module User’s Guide  
7F06-02 Local Management Appendix  
7C03 MMAC SmartSwitch Installation Guide  
7C04 Workgroup SmartSwitch Installation Guide  
7C04-R Workgroup SmartSwitch Installation Guide  
1-4  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
Chapter 1: Introduction  
1.5  
GETTING HELP  
If you need additional support related to this device, or if you have any  
questions, comments, or suggestions concerning this manual, contact the  
Cabletron Systems Global Call Center:  
Phone  
(603) 332-9400  
Internet mail  
FTP  
ctron.com (134.141.197.25)  
anonymous  
Login  
Password  
your email address  
BBS  
(603) 335-3358  
Modem setting  
8N1: 8 data bits, No parity, 1 stop bit  
For additional information about Cabletron Systems or our  
products, visit our World Wide Web site:  
For technical support, select:  
Service and Support.  
Before calling the Cabletron Systems Global Call Center, have the  
following information ready:  
Your Cabletron Systems service contract number  
A description of the failure  
A description of any action(s) already taken to resolve the problem  
(e.g., changing mode switches, rebooting the unit, etc.)  
The serial and revision numbers of all involved Cabletron Systems  
products in the network  
A description of your network environment (layout, cable type, etc.)  
Network load and frame size at the time of trouble (if known)  
The device history (i.e., have you returned the device before, is this a  
recurring problem, etc.)  
Any previous Return Material Authorization (RMA) numbers  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
1-5  
 
Chapter 1: Introduction  
1-6  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
CHAPTER 2  
NETWORK REQUIREMENTS  
Before installing Cabletron Systems 7F06-02 Module, review the network  
requirements outlined in this chapter. All requirements included in this  
chapter should be met to ensure satisfactory performance of the 7F06-02  
Module. Failure to do so may result in unsatisfactory network  
performance.  
2.1  
FPIM MODULE SPECIFICATIONS  
This module uses Fiber Port Interface Modules (FPIM) to provide front  
panel cable connections. The FPIMs are user-installable. Refer to Section  
3.2, Installing FPIMs.  
2.1.1  
FPIM-00 and FPIM-01  
The FPIM-00 and FPIM-01 provide a multimode fiber connection. The  
FPIM-00 uses a MIC style connector and the FPIM-01 uses an SC type  
connector. The specifications for both devices are listed in Table 2-1,  
while the transmitter power parameters are provided in Table 2-2.  
Table 2-1 FPIM-00 and FPIM-01 Specifications  
Worst  
Case  
Budget  
Worst  
Case  
Typical  
Budget  
Parameter  
Typical Value  
Receive  
Sensitivity  
-30.5 dBm  
-7.6 dBm  
-28.0 dBm  
-8.2 dBm  
Peak Input  
Power  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
2-1  
 
 
Chapter 2: Network Requirements  
Table 2-2 Transmitter Power Parameters  
Worst  
Case  
Budget  
Worst  
Case  
Typical  
Budget  
Parameter  
Typical Value  
50/125 µm  
-13.0 dBm  
-15.0 dBm  
-12.0 dBm  
-9.0 dBm  
13.0 dB  
17.5 dB  
fiber  
62.5/125  
µm fiber  
-10.0 dBm  
16.0 dB  
19.0 dB  
20.5 dB  
23.5 dB  
100/140 µm  
fiber  
-7.0 dBm  
Error Rate  
Better than 10-10  
The link distance is up to 2 kilometers on the multimode fiber optic cable  
as specified by ANSI MMF-PMD.  
2.1.2  
FPIM-02 and FPIM-04  
The FPIM-02 has an RJ-45 connector supporting an Unshielded Twisted  
Pair (UTP) connection. The FPIM-04 has an RJ-45 connector supporting  
a Shielded Twisted Pair (STP) connection. The pinouts for both are listed  
in Table 2-3.  
Table 2-3 FPIM-02 and FPIM-04 Pinouts  
Pin Number  
Represents  
Transmit+  
Pin Number  
Represents  
1
2
3
4
5
NA  
NA  
Transmit-  
NA  
6
7
8
Receive+  
Receive-  
NA  
The link distance is up to 100 meters on unshielded twisted pair cable as  
specified by ANSI TP-PMD.  
2-2  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
   
Chapter 2: Network Requirements  
2.1.3  
FPIM-05 and FPIM-07  
The FPIM-05 and FPIM-07 provide a single-mode fiber connection. The  
FPIM-05 uses a MIC style connector and the FPIM-07 uses an SC type  
connector. The specifications for both devices are listed in Table 2-4.  
Table 2-4 FPIM-05 and FPIM-07 Specifications  
Parameter  
Typical  
Minimum  
Maximum  
Transmitter Peak Wave Length  
Spectral Width  
Rise Time  
1300 nm  
60 nm  
1270 nm  
-
1330 nm  
100 nm  
5.0 nsec  
5.0 nsec  
50.7%  
3.0 nsec  
2.5 nsec  
50.1%  
2.7 nsec  
2.2 nsec  
49.6%  
Fall Time  
Duty Cycle  
Bit Error Rate  
Betterthan  
10-10  
The link distance is up to 40 kilometers (max) and 25 kilometers (typical)  
on single-mode, fiber-optic cable as specified by ANSI SMF-PMD.  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
2-3  
 
 
Chapter 2: Network Requirements  
2-4  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
CHAPTER 3  
INSTALLATION/REMOVAL  
This chapter contains instructions for unpacking and installing the 7F06-2  
Module in the:  
7C03 MMAC SmartSwitch  
7C04 Workgroup SmartSwitch  
7C04-R Workgroup SmartSwitch  
Also included in the chapter are instructions for installing the front panel  
FPIMs.  
3.1  
UNPACKING THE 7F06-02 MODULE  
Unpack the 7F06-02 Module by using the following steps:  
Before unpacking the 7F06-02 module, attach the antistatic  
wrist strap included with the SmartSwitch or SmartSwitch  
module by following the instructions printed on the package.  
1. Carefully remove the module from the shipping box. (Save the box  
and packing materials in the event the module must be reshipped.)  
2. Remove the module from the plastic bag. Observe all precautions to  
prevent damage from Electrostatic Discharge (ESD).  
3. Carefully examine the module and check for damage. If damage  
exists, DO NOT install the module; contact Cabletron Systems Global  
Call Center.  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
3-1  
 
Chapter 3: Installation/Removal  
3.2  
INSTALLING FPIMS  
Before installing the 7F06-02 module, attach the antistatic  
wrist strap included with the SmartSwitch or SmartSwitch  
module by following the instructions printed on the package.  
The 7F06-02 module is shipped without FPIMs. To install an FPIM,  
follow the procedure below:  
1. Remove the module if it is installed in the 7C03 MMAC SmartSwitch  
chassis by reversing the procedure in Section 3.3.  
2. Remove the blank front cover over the FPIM slot.  
3. Install the FPIM as shown in Figure 3-1. Ensure that the rear connector  
is seated firmly before tightening the two mounting screws.  
Figure 3-1 Installing an FPIM  
3-2  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
 
Chapter 3: Installation/Removal  
3.3  
INSTALLING/REMOVING THE 7F06-02 MODULE  
The following procedure details the installation and removal procedure  
for the 7F06-02 module.  
3.3.1  
Installing in the 7C03 SmartSwitch  
The 7F06-02 Module is installed in the 7C03 MMAC SmartSwitch  
using the following steps and referring to Figure 3-2.  
Note: The left-most slot in the 7C03 MMAC SmartSwitch is reserved for  
the 7X00 SmartSwitch Module.  
Note: Before installing the 7F06-02 module, attach the antistatic wrist  
strap included with the SmartSwitch or SmartSwitch module by  
following the instructions printed on the package.  
1. As a precaution, power down the MMAC 8 before beginning the  
installation or removal of any modules. At the very minimum, the  
7C03 must be pulled to disconnect it from the power source. Damage  
to modules may result if this procedure is not followed.  
2. Remove the blank panel covering the slot in which the module will be  
installed. All other slots must remain covered to ensure proper airflow  
and cooling.  
3. Install the module by sliding it into slots as shown in Figure 3-2.  
Ensure that the printed circuit board (PCB) is between the card guides,  
slides in straight, and engages the backplane connectors properly.  
4. Using a slotted screwdriver, tighten the top and bottom screws.  
Card  
Guides  
Figure 3-2 Installing the 7F06-02 Module in the  
7C03 MMAC SmartSwitch  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
3-3  
 
 
Chapter 3: Installation/Removal  
3.3.2  
Removing from the 7C03 SmartSwitch  
The 7F06-02 Module inserted in the 7C03 MMAC SmartSwitch can be  
removed upon proper removal of power. Follow the steps below and refer  
to Figure 3-3 to remove the module.  
Note: Before removing the 7F06-02 module, attach the antistatic wrist  
strap included with the SmartSwitch or SmartSwitch module by  
following the instructions printed on the package.  
1. As a precaution, power down the MMAC 8 before beginning the  
installation or removal of any modules. At the very minimum, the  
7C03 must be pulled to disconnect it from the power source. Damage  
to modules may result if this procedure is not followed.  
2. Use a slotted screwdriver to loosen the two screws that secure the  
module to the chassis.  
3. Locate the two ejector tabs on the module (to the right of the screws  
on the top and bottom of the module).  
4. Simultaneously press down on the bottom ejector tab and up on the top  
ejector tab until the module ejects from the backplane.  
5. Grasp both ejector tabs and carefully slide the module out of the  
chassis.  
Screw  
Ejector Tab  
Screw  
Ejector Tab  
Figure 3-3 Removing the 7F06-02 Module from the 7C03 MMAC  
SmartSwitch  
3-4  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
 
Chapter 3: Installation/Removal  
3.3.3  
Installing in the 7C04 or 7C04-R Workgroup  
SmartSwitch  
The 7F06-02 Module is installed in the 7C04 or 7C04-R Workgroup  
SmartSwitch using the following steps and referring to Figures 3-4 and  
3-5.  
Notes: The top slot in the 7C04 Workgroup SmartSwitch is reserved for  
the 7X00 SmartSwitch Module.  
The bottom slot in the 7C04-R Workgroup SmartSwitch is  
reserved for the 7X00 SmartSwitch Module.  
Therefore, before installing the 7F06-02 module, attach the wrist  
strap included with the SmartSwitch or SmartSwitch module by  
following the instructions printed on the package.  
1. As a precaution, power down the MMAC 8 before beginning the  
installation or removal of any modules. At the very minimum, the  
7C04 or 7C04-R must be pulled to disconnect it from the power  
source. Damage to modules may result if this procedure is not  
followed.  
2. Remove the blank panel covering the slot in which the module will be  
installed. All other slots must remain covered to ensure proper airflow  
and cooling.  
3. Install the module by sliding it into slots as shown in the appropriate  
figure. Ensure that the printed circuit board (PCB) is between the card  
guides, slides in straight, and engages the backplane connectors  
properly.  
4. Using a slotted screwdriver, tighten the top and bottom screws.  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
3-5  
 
Chapter 3: Installation/Removal  
1
2
SN  
3
4
Screw  
Ejector Tab  
Figure 3-4 Installing the 7F06-02 Module in the 7C04 Workgroup  
SmartSwitch  
FANS  
4
3
2
1
Card  
Guides  
Figure 3-5 Installing the 7F06-02 Module in the 7C04-R Workgroup  
SmartSwitch  
3-6  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
Chapter 3: Installation/Removal  
3.3.4  
Removing the 7F06-02 from the 7C04 or 7C04-R  
Workgroup SmartSwitch  
The 7F06-02 Module, inserted in the 7C04 or the 7C04-R  
Workgroup SmartSwitch, can be removed whenever necessary. Follow  
the steps below and refer to Figures 3-6 or 3-7 to remove the module.  
Note: Before removing the 7F06-02 module, attach the antistatic wrist  
strap included with the SmartSwitch or SmartSwitch module by  
following the instructions printed on the package.  
1. As a precaution, power down the MMAC 8 before beginning the  
installation or removal of any modules. At the very minimum the 7C04  
or 7C04-R must be pulled to disconnect it from the power source.  
Damage to modules may result if this procedure is not followed.  
2. Use a slotted screwdriver to loosen the two screws that secure the  
module to the chassis.  
3. Locate the two ejector tabs on the module (below the screws on the left  
and right end of the module).  
4. Simultaneously press left on the left ejector tab and right on the right  
ejector tab until the module ejects from the backplane.  
5. Grasp both ejector tabs and carefully slide the module out of the  
chassis.  
Screws  
1
2
3
4
Ejector Tabs  
Figure 3-6 Removing the 7F06-02 Module from the 7C04 Workgroup  
SmartSwitch  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
3-7  
 
Chapter 3: Installation/Removal  
Screws  
FANS  
4
SN  
3
2
1
Ejector Tabs  
Figure 3-7 Removing the 7F06-02 Module from the 7C04-R Workgroup  
SmartSwitch  
3-8  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
CHAPTER 4  
TROUBLESHOOTING  
4.1  
DIAGNOSTIC AND MONITORING SYSTEM  
The 7F06-02 Module uses LANVIEW, Cabletron Systemsbuilt-in visual  
diagnostic and status monitoring system.  
With LANVIEW LEDs the status of each transmit and receive port on the  
7F06-02 Module can be determined, at a glance. This section discusses  
the function and purpose of the LEDs on the 7F06-02 Module.  
Figure 4-1 shows the LANVIEW LEDs of the 7F06-02 Module.  
7F06-02  
SP  
A Link Status  
A
Primary  
Ring  
B Link Status  
F
D
D
I
P
S
A
B
Secondary  
Ring  
1
B
Receive  
Transmit  
Figure 4-1 LANVIEW LEDs  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
4-1  
 
 
Chapter 4: Troubleshooting  
4.2  
PORT RECEIVE LEDS  
Table 4-1 indicates the state of the receive port.  
Table 4-1 Port Receive LEDs  
LED Color  
State  
Yellow (Flashing)  
Off  
Data activity (flashing to steady on indicates rate)  
No activity, port can be disabled or enabled  
4.3  
PORT TRANSMIT LEDS  
Table 4-2 indicates the state of the transmit port.  
Table 4-2 Port Transmit LEDs  
LED Color  
State  
Green (Flashing)  
Off  
Data activity (flashing to steady on indicates rate)  
No activity, port can be disabled or enabled  
4.4  
A/B LINK LEDS  
Table 4-3 indicates the state of the A/B Link LEDs.  
Table 4-3 Link LEDs  
A
P
S
B
State  
Green  
Green  
N/A  
N/A  
Off  
Green  
Green  
Ports Enabled & Active  
Green  
THRU A, MAC on Primary,  
Secondary Bypasses Board  
Green  
Green  
Yellow  
Green  
THRU A, MAC on Primary,  
No MAC on Secondary  
4-2  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
     
Chapter 4: Troubleshooting  
Table 4-3 Link LEDs (Continued)  
A
P
S
B
State  
Green  
Off  
Green  
Green  
THRU B, MAC on Secondary,  
Primary Bypasses Board  
Green  
Green  
Green  
Yellow  
Yellow  
Off  
Green  
Off  
Green  
Green  
Green  
THRU B, MAC on Secondary,  
No MAC on Primary  
THRU, No MAC on Primary,  
Secondary Bypasses Board  
Yellow  
THRU, No MAC on Secondary,  
Primary Bypasses Board  
Green  
Green  
Green  
Red  
Red  
Red  
Red  
Red  
Off  
Yellow  
Yellow  
Green  
Green  
Green  
Green  
Green  
Yellow  
WRAP A, MAC on Primary  
WRAP A, No MAC on Primary  
WRAP B, MAC on Primary  
WRAP B, No MAC on Primary  
WRAP AB, MAC on Primary  
BYPASS Primary & Secondary  
TWISTED A-A, B-B  
Yellow  
Yellow Green  
Yellow Yellow  
Green  
Green  
Green  
Green  
Off  
Red  
Red  
Off  
Yellow Off  
PCM did not complete, Not  
Active  
Red  
Off  
Off  
Red  
Ports Disabled  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
4-3  
 
Chapter 4: Troubleshooting  
4-4  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 
CHAPTER 5  
TECHNICAL SPECIFICATIONS  
This chapter includes the technical specifications for 7F06-02 module.  
Cabletron Systems reserves the right to change these specifications at any  
time without notice.  
5.1  
STANDARDS  
IEEE 802.1D  
IEEE 802.3i 10BASE-T  
5.2  
EMI  
The EMI requirements of:  
FCC Part 15 Class A  
EN 55022 Class A  
VCCI Class I  
5.3  
EMC  
The EMC requirements of:  
EN 50082-1  
IEC 801-2 ESD  
IEC 801-3 Radiated susceptibility  
IEC 801-4 EFT  
5.4  
NETWORK INTERFACES  
Two FPIMs  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
5-1  
 
Chapter 5: Technical Specifications  
5.5  
SAFETY  
It is the responsibility of the person who sells the system to which the  
module will be a part to ensure that the total system meets allowed limits  
of conducted and radiated emissions.  
This equipment meets the safety requirements of:  
UL 1950  
CSA C22.2 No. 950  
EN 60950  
IEC 950  
5.6  
SERVICE  
MTBF:  
>200,000 hours  
<0.5 hour  
MTTR:  
5.7  
PHYSICAL  
5.7.1  
Dimensions  
31.1D x 22.9 H x 3.1 W centimeters  
(12.3 D x 9.0 H x 1.2 W inches)  
5.7.2  
Weight  
Unit:1.8 kgs. (4 lbs.)  
Shipping:4.5 kgs. (10 lbs.)  
5-2  
7F06-02 FDDI SmartSwitch Interface Module User’s Guide  
 

Blackberry Server Enterprise Server User Manual
Black Box Telephone Video Sentry Color Tilt Phone System User Manual
Blanco Indoor Furnishings 506 528 User Manual
Braun Blood Pressure Monitor BP3510 User Manual
Bravetti Fryer F1011H User Manual
Bush Hog Lawn Aerator MPG 720 User Manual
Bushnell Digital Camera 119204 User Manual
Canon Camera Lens EF15 User Manual
Canon Digital Camera 5251B001 User Manual
Carrier Furnace 58VMR User Manual