BlueTrek Headphones SKIN User Manual

BLUETREK® Skin user guide  
Thank you for choosing the BLUETREK® Skin headset, we hope you will enjoy the  
convenience we are bringing to you. The BLUETREK® Skin offers many functions,  
please read this manual before getting started.  
EC-Declaration of Conformity  
We, Innovi Technologies Ltd of  
31/F China Online Centre,  
333 Lockhart Road,  
Wan Chai, Hong Kong  
declare under our sole responsibility that our product  
BLUETREK Skin  
to which this declaration refers is in conformity with the appropriate standards  
EN300 328-02  
EN301 489-17  
EN301 489-01  
EN50371  
EN60950  
Following the provisions of Radio and Telecommunications Terminal Equipment  
directive 1999/5/EC.  
September 2006  
Guillaume Ponticelli, Director of Development  
PAGE 1 / 9  
 
BEFORE USING YOUR HEADSET FOR THE FIRST TIME  
-
Pair the headset with a mobile phone. Please refer to the “Pairing the  
BLUETREK® Skin” section of this manual.  
Introduction  
The BLUETREK® Skin headset is a wireless headset based on the Bluetooth®  
technology. It complies with Bluetooth® 1.2 protocol, supporting Headset and Hands-  
free profile.  
PAGE 3 / 9  
 
Charging the BLUETREK® Skin  
Please connect the charger to the headset and to the main. During the charge, the  
indicator light is red, the indicator light will turn off when the charge is complete. During  
subsequent charges, the charging should take approximately 3 hours.  
When you hear a low-tone beep in your headset at regular intervals, and the indicator  
light flashes in red, your headset needs to be recharged.  
Important:  
If your headset is fully charged, the red indicator light will not turn on when  
plugging into the charger.  
(To check whether your headset is fully charged, plug in the charger and press  
the talk button for approx. 2 seconds. The red indictor light will turn on for approx.  
3 seconds if the headset is fully charged.)  
To maximize battery lifetime, it is recommended to recharge your headset to full  
capacity only when the battery is low, since a battery has a lifetime of about 500  
charging cycles.  
If you leave your headset battery empty for an extended period of time, it could  
excessively discharge the battery. In this case, charge your headset for 3 hours  
or more until the battery recovers and recharges completely. When you first  
charge the headset after prolonged storage, it may take few minutes for the red  
indicator light to turn on.  
Do not charge your headset for more than 10 hours.  
The use of any other charger will automatically suspend the warranty. It is strictly  
forbidden and can be very dangerous.  
Pairing the BLUETREK® Skin  
Before using the BLUETREK® Skin headset, you must pair it with your Bluetooth®  
mobile phone. Pairing is the process of linking 2 Bluetooth® devices, so that they can  
communicate.  
To initiate pairing:  
1. Place the BLUETREK® Skin and your mobile phone within 0.3 meter (1 foot) from  
each other.  
2. Switch on your phone and select its Bluetooth® discover mode (refer to the  
Bluetooth® mobile phone user manual).  
3. When the BLUETREK® Skin is switched off, press and hold the TALK button for  
about 7 seconds until the indicator light flashes red and blue alternately. And a  
sound can be heard in the speaker.  
4. Once the mobile phone detects the headset, a “BLUETREK Skin” message will  
be displayed. Follow the phone instructions to accept the pairing. The PIN code  
(or passkey) is 0000, then press “yes” or “ok”.  
If pairing was successful, the indicator light will switch to blue and flashes slowly.  
If you haven’t started the discovery mode within 5 minutes, the headset will switch off.  
You must then switch on your headset and start the pairing again.  
PAGE 4 / 9  
 
Wearing the BLUETREK® Skin  
For your convenience, the ear hook of BLUETREK Skin is designed to be removable  
and adjustable which allows the headset to be worn on either ear. BLUETREK® Skin,  
as packaged, is ready to be worn on your right ear.  
For left ear, simply unsnap the ear clamp  
from the headset by pulling gently at the  
case of the ear clamp ring.  
The ear hook is made of a soft material  
which can be shaped to fit your ear.  
Flip the ear clamp over, and snap it back  
onto the headset by applying gentle  
pressure on the case of the ear clamp  
ring.  
Switching the BLUETREK® Skin ON and OFF  
Switching BLUETREK® Skin ON  
When your headset is off, press and hold the TALK button for about 2 seconds until the  
blue indicator light is on. A beep (2 tones) can be heard in the speaker. Release the  
TALK Button.  
To check if your headset is ON, press once on the TALK button. If the indicator light  
flashes blue, it means your headset is ON.  
®
Switching BLUETREK Skin OFF  
When your headset is on, press and hold the TALK button for about 5 seconds until the  
red indicator light is on after the quick blue flashes. A beep (2 tones) can be heard in the  
speaker then release the TALK button.  
PAGE 5 / 9  
 
Making a call  
*Mobile phone with voice recognition  
. Make sure the voice recognition function on your mobile is activated and your voice  
tags have been recorded with the phone. To enter these, please refer to your phone’s  
manual  
. When there is no incoming or active call, press once on the TALK button  
. Wait for the audio signal sent by the mobile phone (generally a short tone).  
. Speak the name of person you wish to call.  
Mobile without voice recognition  
. Make sure both the headset and the mobile phone are ON and in stand-by mode.  
. Dial the number on the phone keypad, after approximately 2 seconds the audio  
connection will be established.  
*This function may not be available on some phones, please refer to the trouble  
shooting frequent asked questions in our website: www.bluetrek.com. to find out more.  
Answering a call  
When the headset rings, press once on the TALK button to take the call.  
Ending a call  
Press once on the TALK button to end an active call.  
Adjusting the volume  
To increase the volume during an active call, press the “VOL+” button on the headset.  
To decrease the volume during an active call, press the “VOL-“ button on the headset.  
Muting the microphone  
To mute the microphone during an active call  
During an active call, press and hold the VOL+ button for approximately 2 seconds. A  
periodic tone can be heard in the speaker when the microphone is muted.  
To end the mute function  
When the microphone is muted, quickly press the VOL+ button on the BLUETREK® Skin.  
The periodic tone will end.  
Transferring a call from BLUETREK® Skin to the mobile phone  
During an active call, press the TALK button for about 2 seconds.  
(This function only works in the Hands-Free Profile.)  
In the Headset profile, you can simply turn off your headset.  
Transferring a call from the mobile phone to the BLUETREK® Skin  
During an active call on the mobile phone, press once on the TALK button to transfer  
the call.  
PAGE 6 / 9  
 
Pre-registered numbers feature  
This feature allows you to store your 2 favourite numbers in your BLUETREK® Skin  
headset and to dial these numbers directly from your headset.  
(Important: This feature is only available in the Hands-free profile).  
Storing your favourite numbers  
1) Ensure your BLUETREK® Skin headset is paired and connected with your phone.  
2) Enter numbers following the syntax describe below as your mobile phone name  
(Please refer to your mobile phone manual to change your phone name. In most  
phones, the mobile phone name is under the “Bluetooth” menu).  
Example 1: To store “0123456789” in position 1 = 1S0123456789T  
Example 2: To store “+44123456789” in position 2 = 2S+44123456789T  
PAGE 7 / 9  
 
3) Press and hold the “Vol-“ button on your BLUETREK® Skin headset for approx. 3  
seconds, until the purple indicator light is on. (A beep can be heard in the  
speaker).  
4) - If the number is correct and have stored in the headset, you will hear:  
1 beep in the speaker and the blue indicator light will flash once if the number has  
been stored in position 1.  
OR  
2 beeps in the speaker and the blue indicator light will flash twice if the number has  
been stored in position 2.  
- If the number is incorrect, it will not store in the headset. You will hear a long low-  
tone beep in the speaker and the red indicator light will flash twice.  
Note:  
1. Only 1 telephone number can be stored at one time. To store the second  
number, simply repeat from Step 2.  
2. Maximum of 2 favourite numbers can be stored and can be replaced by  
repeating the above steps.  
3. Remember to change back your mobile phone name once you have stored the  
numbers.  
Making a call to one of the stored numbers  
1) Ensure your BLUETREK® Skin headset is paired and connected with your phone.  
2) Press and hold the “Vol +” button on your BLUETREK® Skin headset until you  
hear:  
-
-
1 beep to call your number stored in position 1;  
2 beeps to call your number stored in position 2.  
Call waiting  
When you hear a call waiting alert while you are on a call, press approx. 3 seconds on  
the TALK button to accept the second call and place the current call on hold.  
To switch between an active call and a hold call, press approx. 3 seconds on the TALK  
button.  
To end the active call and take the hold call, press once on the TALK button.  
This function may not be available on some phones.  
Additional features with some phones  
Rejecting a call  
When the headset rings, press the TALK button for about 2 seconds.  
Redial the last number  
When there is no incoming or active call, press the TALK button for about 2 seconds  
until you hear a beep.  
PAGE 8 / 9  
 
Troubleshooting guide  
The first thing you should do when encountering a problem that you cannot solve with  
this manual, is to switch off your headset and your mobile phone, and switch them on  
again.  
To find out more, please refer to the trouble shooting frequent asked questions in our  
website: www.bluetrek.com.  
Guidelines for safe use  
Read those guidelines before using your headset.  
-
-
-
-
-
Do not drop or try to alter the shape of your headset.  
Do not expose your headset to liquid or moisture.  
Do not expose your headset to extreme temperatures. Temperature range: 0-40C.  
Do not expose your headset to fire or open flames.  
Do not try to disassemble your headset. Service and Maintenance can only be  
performed by BLUETREK® dealers.  
-
-
Keep your headset away from dust and dirt.  
Do not let children play with your headset, since it contains small parts that could  
become detached and create a choking hazard.  
-
-
Check the regulation in your area if you plan to use your headset while driving.  
Turn off your headset before boarding an airplane.  
CAUTION : Danger of explosion if battery is incorrectly replaced. Dispose of batteries  
according to local regulations. Do not dispose as household waste.  
PAGE 9 / 9  
 

Black Box Marine Safety Devices 1101 User Manual
Black Decker Drill SP1400D User Manual
Bosch Appliances Home Security System APC AMC2 4W User Manual
Briggs Stratton Portable Generator PRO8000 User Manual
Brinkmann Gas Grill Outdoor Charcoal Wood Smoker Grill User Manual
Bush Hog Automobile Accessories SRG60 User Manual
Canon Digital Camera 115 HS User Manual
Carrier Blower 58SSB User Manual
Chamberlain Garage Door Opener 1000E 1 4 HP User Manual
Cisco Systems IP Phone OL 23091 01 User Manual